How to paint a motorcycle gas tank with spray paint

how to paint a motorcycle gas tank with spray paint

How to Paint a Motorcycle Gas Tank

Jan 05,  · Spray it horizontally and don’t forget to shake the rattle can before spraying. Also, don’t forget to wipe off or clean the spray nozzle every time before spraying. You don’t need to make a thick layer but cover thin all the corners of the gas tank. Make an interval of at least 30 minutes in between each . How to Paint a Motorcycle Tank: 6 Steps (with Pictures.

Not every motorcyclist do motorcycle works yow his or her own. But Most of the enthusiasts do or try to spay. Meanwhile, obviously, some of them have the question, can we paint any part of the bike on our own? Simply the answer is yes.

So stay here until the end. Of course, painting the motorcycle parts is an expert hand job no doubt. But obviously, it needs concentration, patience, and a specific sequence of procedures.

Furthermore, the right setup of tools and equipment can make the work lot easier to do. Does it worthy? Would it be durable? Answering all of the questions we should say, motorcycle painted parts are very small parts to be painted. Hence, with the proper application, an aerosol spray paint or rattle can spray also can give you a professional-like finish.

It also can be durable if proper procedure and precision applied. This type hw simple and small job can cost you even thrice or four times more. So rattle can spray paint is far more convenient dpray do low-cost custom paint. So whatever painy let come to our topic. For the betterment of understanding here we are taking the motorcycle fuel tank to paint it with a rattle can.

So before the task please paing collect the following equipment for the job. So these are the equipment you need to collect before the painting job. Keep all the equipment aside on the table and keep adequate free space for your work. One more thing you needed that is enough lighting arrangement at your workplace. Before starting the paint job, first, get the gas tank and other parts detached from the motorcycle.

Make the gas tank empty of fuel and spgay the fuel in a safe area. Then detach the tank cap and fuel cock from the tank. If necessary clean the inner side of the gas tank for the rusts or repair if further needed. Actually, you have to determine your job set of painting at first of all. Then you have to prepare accordingly, what kind of paintwork you decided to do. Whatsoever, you can do completely a new color or keeping the same color scheme.

Further, there are options to choose from. You can choose the matt finish or some glossy. Or can completely customize the color scheme on your own. So select your choice at first. So whatever your choice, collect the desired coded rattle can spray. If there is some matt finish then you can select the 1K coating. For multiple color-scheme or customized glossy finish can go for the 2K coating. But 1K coating is much more convenient for such kind of small job. In the case of custom sticker-design or custom color-scheme, you can apply a clear coat or hardener after the final touch.

It will smoothen the total paintwork in one. So whatever your expectation, do the planning earlier and if necessary do some sketch on the tank or on papers. Also can do experimental work on a metal sheet. Inspect the stock color condition of the gas tank. If the tank is rusted completely, then you have to strip off all the rust and damaged paint.

How to cover earphones with yarn you have to remove all of the base layer and primer applied by the manufacturer. If the gas tank color is quite ok or just faded away, and few dents or color damages are there, keep the base layer. So, inspect the stock color and base layer condition first.

So get some gas in a cotton rag and rub it what to get someone who has lost a loved one on the tank. See the outcome. If it found unchanged then rub it with medium-grit sandpaper. If the base layer found pajnt then keep it and even the paint if it in good condition. Only striping the upper layer off with medium-grit sandpaper is okay in such a case. Otherwise, do strip what is a locality payment layers off completely which are damaged.

So when to strip-off all the color and base-layer completely then you can use the color stripper chemical. Whatever the condition is depending on it do use proper grit of sandpaper. Strip off the weakened layers and clean the surface completely of paint, oily sediment, and other types of stains.

Cleaning off the weakened color or the worst base layers inspect the gas tank surface again. Mark the dents or piant. Fill up the dent, scratch, and uneven gaps with the dent filler.

Scrap it smoothly with a scrapper and let it dry completely. After drying the dent filler scrub it and smoothen it to the how to install pex water tubing. If necessary touch up with dent filler again, dry it off, and smoothen again with proper sandpaper.

Remember, these preparations are more than half of your total painting job. So do it carefully with patience. It will give the paint a life long.

So the gas tank is completely ready making up with stripping, dent filling, and smoothening off. You just reached the second part of the painting job. Get the painting area also clean and dust-free. Arrange proper lighting setup and keep the workplace warm. First of all, hang the gas tank from the what is amerenue phone number and get it to a comfortable level. Hold a convenient part which can be finished at the last.

Apply the base layer or primer coat thoroughly directing top to bottom from a recommended distance. Make an interval of at least 30 minutes in between each coat. So after applying the base layer, inspect it again thoroughly for flaws.

If necessary use the smallest grit or Zero-Grit sandpaper to smoothen it and dust off. Then it ready to apply the desired colors or designs therefore the final paint job. If you are doing a single color, then apply the specific code of rattle can spray. You can do matt or glossy finishes. So use the 1K coating. But if you are desired to put a glossy finish or multiple color-schemes or sticker work then the job is different. Then you have to work with multiple layers painting multiple times.

In such a case, apply the base color first. Follow the same procedure that you followed to apply the primer. Use secondary color if necessary. Allow adequate time intervals for proper drying off each layer. Before the finishing job, do inspect thoroughly the gas tank for any errors or flaws. Inspect for the uneven painh between colors or the sticker margins. If necessary Use the zero-grit sandpaper carefully to smoothen it. Then dust off the gas tank carefully. Now motorcycld ready for the final clear coat or finish.

When doing the finishing job, be more careful as you are at the final stage of your entire paint job. So do it patiently and carefully.

Never allow airflow in the room to avoid air dust. Keep the room warm arranging laint proper lighting system. Spray from a proper distance and spray the rattle can in direction of top to bottom horizontally. Do it thoroughly and make thin layers. Allow proper intervals in between the coats to dry off properly. And keep it hanging in the warm room. So you are done with your job. Of course, aerosol spray paint or rattle can contain harmful gases.

Also, the color spray can get inside the lungs with breath.

Preparing the Gas Tank for Your Paint Job

One of the better parts of building a custom bike after riding it…! A great way to do this is by painting your bike, and one of the most prominent parts is the gas tank. Some people just go to a paint shop and let someone else do it, but I prefer doing it myself. There are a lot of different ways and some people have some other tips and trick, but these steps gave me the result of a professional looking paint job!

For this you need:. In this case you can forget about thinner and rough sanding paper only and up for removing the color layer. A good preparation is everything when it comes to painting. This sounds a bit obvious, but it starts with removing the gas tank from your bike. Before you remove it, be sure that there is no fuel left. If you have fuel left in the tank:. When most of the fuel is removed you need to close the valve s so you can remove the gas tank off the bike. When there is still some fuel left, you can hold the tank above the funnel and reopen the valves again.

When the tank is off: remove the gas cap and valve s and protect the openings. You can also just protect them by wrapping them in tape. For this you need some rough sanding paper — grit and a sanding block.

So roll up your sleeves, find a good position and start sanding with the lowest grit, moving up to the grit and sanding block. Please note that this takes a while! If the tank is in good condition without rust or bits in it, you can choose to work only to the original primer and start from here. Put some thinner on the cloth and rub the tank in. Tip: also check the inside of your gas tank! As mentioned before, the biggest part of the paint job is the preparation, but now you can actually start spraying but still needs a little sanding…!

Important: only use automotive spray paint Important: keep a good spray distance; 8 to 10 inches away from the surface. You need a minimum of 3 layers, but 4 or 5 is better. Every layer should be applied like this:. Let this first layer dry for about 30 minutes please be sure to follow the instructions on the can and then repeat this process for every layer.

After your last layer: let it dry for a 1 or 2 days the longer, the better. The technique is pretty much the same as with the primer coats. Before you start painting, make sure that the surface is clean. For this you can use the wet and dry cloths. The clear coat gives your paint job extra protection. Bring on 1 or 2 layers, using the same technique as with the primer and color coats. And then: let it dry again! The extra mile? Grab your sanding gear very fine grit, wet. And yes: this is the last time!

Just remove dust and bits and grab your buffing cloth and wax. This extra step will give a very nice and super shiny effect. Cool huh?! I hope that this post will help and inspire you to paint your motorcycle gas tank yourself. But if you have some constructive feedback or some more tips: please let me know! Check out this post! Off course you don't want your project to end up as an "unfinished project" on a classifieds website Exactly one year ago I've launched BikeBrewers.

With this post I'll try to inspire cafe racer enthusiast to start working on their own Low Budget Cafe Racer. I think it's not necessary…. The gas tank respray sounds great and I did it but when I put petrol in and spilt some on the tank,,,the paint ran everywhere. What did I do wrong? What do I put on the sprayed tank that is petrol resistant?

Thanks Gary. How many layers of primer, paint and clear coat did you apply? And how much time was between them? Thanks for your instructions. I am about to tackle this myself. Also put a 60 dollar truck on it.

I had bought some Street glide badges for the tank. When I got there he was putting them on the tank. I ask him how much money he wanted after always telling me he was not going to charge me anything because it was a school project. When I got the parts back to the guy who tore it down. But I must say it did look good. Now 2 years later it looks terrible. So I am going to paint it this time myself. With spray cans. Randy Barger. You can also get them to chemically dip it to a shotgun metal no primer required it will halt oxidization and you can clear coat it once dry and it looks sick.

It can make or break a build, or the overall perception of your bike.. Your email address will not be published. We roll on our readers submissions, so if you want to show off your custom motorcycle: submit your brew! Thank you for subscribing. Something went wrong. Skip to main content Skip to secondary menu Skip to primary sidebar Skip to footer Home Submit your brew! Always read and follow the instructions from the products u use, especially with primer, paint and coating!

If you want to bring on details or striping, this is the moment. Views: 2, Related Posts. Comments The gas tank respray sounds great and I did it but when I put petrol in and spilt some on the tank,,,the paint ran everywhere.

What paint did you use? Do you sand after the primer to make it smooth for paint? Nothing listed here. Good luck! What are good paints and primers to use for this? Leave a Reply Cancel reply Your email address will not be published. Footer BikeBrewers. Photo credits Guest bloggers Newsletter Privacy Advertise. Search The Blog Search the site Newsletter Signup Sign up and be the first to see new custom bikes!



More articles in this category:
<- How to draw frost mw3 - How to apply for job visa in dubai->

Comment on post
2 comments

Add a comment

Your email will not be published. Required fields are marked *