How to hook up line out converter

how to hook up line out converter

How to Connect a Car Stereo Line Out Converter

Jul 22,  · We are finally going to take you through Line Output Converters (LOC). Learn what they are, what they do, whether or not you need one and how to install and. How to Connect a Car Stereo Line Out Converter by Travis Corkery. Remember the days when we hooked stereo systems up with stripped-bare and twisted wires stuck into little spring-loaded clamps? At least in the aftermarket and consumer audio world, that method has long since been replaced by coupling with plug-in RCA jacks.

Log in or Sign up. Tacoma World. Welcome to Tacoma World! You are currently viewing as a guest! To get full-access, you need to register for a FREE account. Post Reply. I'm sorry if this has been answered in other threads, I searched but did not find it in the threads I read. I am trying to hook up a line output converter to my stock trd or head unit, not the jbl system.

I have an amp and subwoofer I'm trying to add and have most everything set up, but I don't know what to do with the remote wire, and do not know if that is the only wire I need to plug into the head unit.

I am an audio noob so any help is appreciated! I've been told it's plug R29 ljne 6 but can't seem to conberter any diagrams kp to what I'm seeing, anyone know what to do? There are plug and play ilne available in the marketplace. I have had a recent run in with a supplier that has one so I apologize for not being willing to provide a name or part number. Do some research and you should be able to find what how to restring an accoustic guitar need.

Sorry for not being able to help further. Exracer2Apr 13, Here you go. YotabillyApr 13, Go to Amazon and search "add an amp Toyota Tacoma". There is a plug-and-play solution that I used to get RCA connectors.

It works very well and is easy as pie. MKWApr 13, Thanks guys, I'll report back for future reference if I end up doing something else. Show Outt Content. Convertre Categories. Metra 87 - 94 Toyota Vehicle Harness. Username or email address: Do you already have an account? No, create an account now. Yes, my password is: Forgot your password?

Meet Dave Delamere

Apr 14,  · I am trying to hook up a line output converter to my stock trd or head unit, not the jbl system. I have an amp and subwoofer I'm trying to add and have most everything set up, but I don't know what to do with the remote wire, and do not know if that is the only wire I need to plug into the head unit. I am an audio noob so any help is appreciated! After you bring up the gains on each channel, it’s time to connect the converter outputs to the aftermarket amplifier. 3. Connect RCAs from the converter to your amp. It is crucial to make sure the input gain/sensitivity knobs on the amp are turned all the way down. Oct 22,  · Good information to know on the line out converters, i used one on my civic to add an aftermarket sub and amp but over time I ended up replacing everything with aftermarket. Just never could get everything to sound right with the factory head unit. .

The idea is to send the hottest signal possible out of the converter, without distorting the output of the converter, and also not going over the max input gain of the amp.

This helps ensure you get the cleanest signal to your amp as possible. For example, if the max input gain sensitivity of your amplifier is 5 volts, we will want to make sure the output of the converter does not go over 5 volts. Before you begin, do not connect the RCA outputs of the converter to the aftermarket amp yet. Only have the speaker level inputs from the factory system connected to your converter, plus 12 volt and ground.

If you are not using signal sense, you will also need a 12 volt trigger wire connected to the converters Remote In terminal in order for it to turn on. For example, if the head unit goes to 40, bring the volume up to about Slowly bring up each channel gain until the maximized light begins to flicker, and then back off until it stops. It serves as a guide in helping you not distort the input of the amplifier see below for more info. This will ensure the amp will be able to accept the highest level signal that it is rated for.

We do this because most amplifiers can accept between 4 and 6 volts. Our converters have 12 db of gain and have the potential to output up to 8. How do I set the output gains on my line converter to match the input sensitivity of my aftermarket amplifier? To do this, we need to properly set the gains on the converter. Set the level on the factory head unit. Bring the gains up on the converter Slowly bring up each channel gain until the maximized light begins to flicker, and then back off until it stops.

The maximized light lets you know you are getting to distorting the output of the converter. Was this article helpful? Yes No. News Latest News Press Releases. Knowledge Base Search Search For. Need Support? Pin It on Pinterest.



More articles in this category:
<- What internet speed do i need for ps4 - How to go to lotus desaru from singapore->

Comment on post
0 comments

Add a comment

Your email will not be published. Required fields are marked *